|
 HOW
TO ORDER
Step 1:
Select badge type
from any of the options on the right.
Step 2:
Send us the details of
how you would like your badge to look and your artwork.
Step 3:
We will email
a quote back to you within a day or so.
Step 4:
Once you have
decided to proceed we will organise a proof for your approval.
Turnaround
Time:
Normally 21 days on
your approval of artwork.
Please Note:
If you are unsure
or would like any other information please
contact us.
info@badgeworks.co.nz
Ph: 04 380
6069 |
|
LAPEL
PINS / METAL BADGES
Lapel Pins & Badges come in full colour graphics and range from a
high quality jewellery like finish with hand crafted detail to a die
struck pin with an antique finish.
|
 Die
Struck Cloisonné - Hard Enamel |
|
 |
Cloisonné Badges offer a high quality
jewellery
like finish with hand crafted detail.
The enamel pins are
twice kiln fired then hand polished and offer scratch and
fade resistance.
Hard Enamel
is the most hard wearing but tends to be the most
expensive because of the the care taken in production.
|
|
Die
Struck Soft Cloisonné - Imitation Soft Enamel
|
|
 |
Soft
Cloisonné replaces
parts of the hard enamel pins because of similarity to
hard enamel material, lower cost, with a wider range of
colours to choose from.
|
|
Die
Struck Copper or Brass Soft Enamel |
|
 |
Copper or brass soft enamel is an ideal
material for 3D cubic designs or designs requiring fine
details. All die struck soft enamel pins colours are
separated by a fine raised line usually gold or nickel
silver which is then polished.
Clear
epoxy resin may be applied.
|
|
Die
Struck Iron Soft Enamel |
|
|
Die struck iron soft
enamel offers a similar finish to above but is a slightly
cheaper option using less expensive materials during
manufacture and can be arranged to suit most budgets.
Clear
epoxy resin may be applied.
|
|
Photo
Etched Soft Enamel |
|
|
Photo etching is normally
carried out on lighter weight material of 0.8mm thick -
usually
brass, photo etching is a good choice for large sized
designs. It is cheaper and lighter than die struck soft
enamel pins while allowing the same number of colours. Photo etching can not be made in 3D cubic design because of
the thickness of material.
Clear enamel resin may be applied.
|
|
Die
Struck Badges - Without Colouring |
|
|
Die
struck badges with out colouring is where materials copper, brass
or iron is used.
Finishes may include sandblasting; two tone (gold and
nickel) finishing; antique finishing; stain or matte effects
and different texture backgrounds.
|
|
Printed
Pins |
|
 |
Either offset
or silkscreen printed offering full colour reproduction with
outstanding detail onto either brass, aluminium or stainless
and then kiln fired after which they are design cut.
Clear
epoxy resin may be applied. |
|
|
|
Metal Badges |
|
High
quality affordable lapel pins and badges to suit every
requirement. |
|
Numbers |
|
We have no
minimum orders and are happy to carry out that special order
but less than 100 badges can be a very expensive option. |
|
Sizes |
|
Lapel Pins start around 15mm with a simple butterfly
clutch pin but as a larger badge they are fitted with a safety
clip or magnet as required. |
|
Prices |
|
Lapel Pin and Badge prices can be tailored to suit any budget.
|
|
Graphics |
|
You supply your artwork or logo in electronic format either .jpg
or windows .bmp with minimum 300dpi resolution - 600 dpi
works best. |
|
Design |
|
If your not sure
about your artwork or what works
best, let us design something for you. |
|
Lead time |
|
Please
allow 21 days for mass production from customer approval of
proof. |
|
|
